© 2017, Norebro theme by Colabr.io Team, All right reserved.

How To Use A Brad Nailer?


Jack Gordon - March 16, 2019 - 1 comment

Woodworking is an art that one learns with time. There are countless tools that come into action while woodworking and brad nailer is one of the biggest contributors.

The tool is available in different power sources and primarily used for attaching smaller moldings and trim in a woodworking project. You can call it a baby sibling to the finish nailer.

Brads are thin in profile and often come in action where finish nailer can’t be used. However, both these tools are bind with each other and often regarded as complementary.

The tool is handy and used for attaching thin strips and delicate trims. However, it might give you a hard time piercing through hardwoods and manufactured woods.

There are certain steps related to the usage of a brad nailer. Let’s see:

1. Using the Right Hose Adaptor

This step is essential for the users of a pneumatic brad nailer. It has to be attached to a hose adaptor for working. Therefore, you need to make sure that the hose adaptor is compatible with the brad nailer.

Other than this, you also have to purchase Teflon tape and pneumatic tool oil. The Teflon tape ensures the grip and holds the connection between the hose and the device itself.

2. Wrap the Connector with Teflon Tape

In the next step, you have to wrap the fitting on the hose adaptor by using Teflon tape. Make sure that the device is tightly connected to the adaptor.

Also, work closely to tighten the connection further by using the adjustable wrench. This is to ensure that no air is leaking.

3. Lubricate the Device

It is important to lubricate the device in order to ensure its seamless working. You should know that the air piston is used by the brad nailer to operate. That is why you must lubricate the adaptor by using pneumatic tool oil. It does not require a lot of oiling.

Only a few drops of it can suffice. Make sure to clean the mess by using a rough cloth. Also, carefully clean the nailer so that it does not slip away from your hands.

4. Loading the Brad Nailer

The tools can be easily loaded with a specific number of nails in it, depending on the model that you are using. Make sure that the device is loaded with a sufficient number of nails that will be required for the entire project.

5. Connecting Device to the Air Compressor

In the next step, you should let the air compressor to pressurize before the device is connected. Soon after the air compressor is ready, immediately connect one end of the hose to the compressor and the other end to the brad nailer.

Make sure that the connection is tight enough. You can use the adjustable wrench to tighten the connections if they are loose.

6. Device Testing

Before making the actual attempt, it is important to check the device on an unwanted piece of wood. This will help you know if the tool is working properly or not.

Simply, hold the handle and place it into position while making sure that nothing gets in the way as you use the tool. The tip of the tool has to rest on the surface of the wood at an angle of 90 degrees.

After that, you just have to pull the trigger and allow the nail to sink inside. If the tool is working properly then you should start with the real project.

The handling of the tool should be done carefully. It uses pneumatic power and causes a blast as the nail is pierced inside the wood. Make sure you handle the tool very carefully.

Using Brad Nailer on Engineered Hardwood

Natural wood is different from the engineered hardwood. The latter one is a solid wood floor product, manufactured from thin planks of hardwood layered together in order to ensure good strength and durability of the product. While a flooring nailer is mostly recommended to be used with the hardwood but a brad nailer, if used properly, can make a second close choice.

  • Setup the nailer and turn on the compressor. Make sure that the hose is attached and is getting sufficient pressure. Apply a few drops of pneumatic tool oil in the fitting on the closing of the nailer.
  • Open the magazine and load it with a sufficient number of nails that you will be using in the project. Make sure to fill the clip with 1 ½ inch nails.
  • Now, set the first row of boards spaced ½” away from the wall using a solid wood spacer.
  • Make sure to put safety glasses on while attaching the air hose with the nailer. Now, attach the nailer by pulling down on the brass ring that surrounds the fitting on the end of the air hose.
  • Insert nipple fitting firmly in the hose fitting. As the nailer is pressed inside the fittings, release the brass ring to lock the tool in its place. Now, just remove the gun by pulling back on the ring.
  • Now, by placing the brad nailer plunge on top of the plank, simply tilt the gun so that the plunger is tiled on an angle of 45 degrees.
  • Simply being in this position, press the plunger tip firmly. This way, you will achieve the gun’s safety mechanism. Now, by firmly holding the gun, you have to squeeze the trigger. Its time to check the nail that has been driven in the flush. Tap the heads of the nail if there is any protrusion by using a hammer. 

Safety

Brad nailer is mostly considered as a safer tool if compared with the finish or framing nailer. The reason is the small size of the nails that it fires. However, this doesn’t mean that one can get potentially wounded in the process of using the nailer.

Therefore, it is important to take some safety measures while working with this tool.

  • Always wear safety glasses so that no stress and harm can come to your eyes.
  • Wear some kind of hearing protection because the nailer causes a lot of noise while firing nails. So, make sure to protect your ears.
  • Wear clothes that are not too loose so that they don’t hinder the working.

Please note that the pneumatic brad nailers don’t use a lot of compressed air to operate. Make sure that you don’t feed the nailer with too much of the compressed air. These are easy to power tools.

With all that said, the biggest question that surface here is the most advantageous models in brad nailers. Well, we have a comprehensive guide on the niche and some amazing recommendations. Find the honest and most dependable models in best brad nailers with us.

Check out these guides if you need help to choose between 18 Gauge Brad Nailer VS 16 Gauge Brad Nailer:

Brad Nailer VS Finish Nailer

18 Gauge Brad Nailer VS 16 Gauge Brad Nailer

Related posts

1 comment

  1. […] The benefit of an 18-gauge nailer is that it creates smaller holes in the wood that are not very evi…. It is also used for specific jobs that don’t require high-density nails. […]